Automation Products

Product Details:

We supply Solid State Relay with and without heat sink, SSR relay board from reputed manufacturers. Product range from AC and DC inputs and various current output ranges.

Product Details:

Since our inception, we are engaged in supplying a wide assortment of Counters. Our range is available in universal, cyclic & sequential timers and is known for its longer functional life, reliability, dimensional accuracy and wear & tear resistance. Moreover, our range is 100% checked and tested by our team of quality controllers to ensure that only quality products are delivered at clients end.

OKY CM Series Thumb Switch type Counter with following features:

• Low cost, Effective, Easy to use Keyboard based Digital Counter
• 4-Digits, Single Row Display
• Programmable ON Delay/Interval mode
• Programmable Input Count Speed
• Programmable Up/Down counting
• Programmable Front Reset
• Programmable Scale factor 0.001 to 9999
• Programmable Auto Reset/Latch output/T.P.R modes
• Programmable Output 2 as Auxiliary contact or Batch control output
• Count Setting via Keyboard
• Available 12 VDC Sensor Supply (Short circuit protected)
• Memory retention up to 10 years
• Configuration at power on (To prevent unauthorized tampering)
• Universal supply voltage ranges from 90 To 270 VAC
• Available in 5 Standard DIN sizes

Product Details:

Product description

• 4 (AIMS-4X) or 8 (AIMS-8X) Analog Input Channels
• Input Type Versions :
  • AIMS-4U / 8U : Each Channel Independently Configurable for Thermocouples, RTD Pt100, Volts, mV, and mA (No Jumper Settings)
  • AIMS-4D / 8D : Each Channel Independently Configurable for DC V / mA (No Jumper Settings)
  • AIMS-4P / 8P : All Channels RTD Pt100 (3-Wire)
  • AIMS-4T / 8T : Each Channel Independently Configurable for Thermocouples / mV (No Jumper Settings)
• 16 Bit Sigma-Delta ADC (± 32,768 Counts)
• Automatic CJC for Thermocouple & LRC for RTD Inputs
• User Settable Scalable Range for DC V/mV/mA Inputs
• 4 Programmable Soft Alarms for each Channel with LED Indicators
• Process Values Available as both 16-Bit Signed Integer & 32-Bit Single Precision Float
• Fast Channel Update Rate
• Three-way Isolation Eliminates Potential Ground Loops between Power, Inputs and RS485 Serial Port
• 2-wire, Half-Duplex, Start-Stop Synchronized RS485 Serial Port
• Industry Standard MODBUS RTU Protocol with Programmable ID, Baud Rate & Parity
• Compact DIN-Rail Mount Enclosure : 22.5(W) X 101(H) X 119(D), mm
• Wide Supply Voltage Range : 18 ~ 32 VDC (24 VDC Nominal)
• Free PC Tool for Easy Configuration and Parameter Settings

Product Details:

WECON make AC Servo Motors 
60 Series

Specification :
Rated Power : 0.4 KW
Rated current : 2.5A
Rated Torque : 1.27 (N-m)
Maximum Torque : 3.71 (N-m)
Rated Speed : 3000 RPM
Brake : Yes

Product Details:

Ultar Sonic Proximity  Sensor - Pefferl + Fuchs

Single head system, Analog output 4 mA ... 20 mA, Measuring window adjustable, Selectable sound lobe width, Series: -18GM, Operating voltage: 10 ... 30 V DC , ripple 10 %_SS, Output type: 1 analog output 4 ... 20 mA, UL approval: cULus Listed, Class 2 Power Source, CCC approval: CCC approval / marking not required for products rated ≤36 V, Connection type: Connector plug M12 x 1 , 5-pin, Housing: brass, nickel-plated

Additional Information:

• Delivery Time: 2 weeks

Product Details:

Safety Light Curtains (Standard Type)

The SFL series safety light curtains are installed in potentially dangerous or hazardous areas to safeguard personnel from injury. The light curtains feature proven technology from Autonics area sensors and mapping sensors. The light curtains are built to meet international safety standards and regulations. Various detection models (finger/hand/hand-body detection) and safety functions are available for diverse applications.

Product Details:

QIS offers wide type/range of Timers.
Our range is available in universal, cyclic & sequential timers and is known for its longer functional life, reliability, dimensional accuracy and wear & tear resistance. Moreover, our range is 100% checked and tested by our team of quality controllers to ensure that only quality products are delivered at clients end.

OKY CM Series Thumb Switch type Counter/Timer with following features:

• Low cost, Effective, Easy to use Push wheel based Digital timer
• 3-Digits, Single Row Display
• Programmable timer start modes to suit various applications
• Programmable ON Delay/Interval mode
• Programmable Up/Down counting
• Programmable Auto Reset/Latch Output
• Programmable Front Reset
• Programmable Memory Backup
• Programmable Output 2 functions: Auxiliary contact/End of cycle/Instant contact
• High Accuracy: 0.05% of Full scale (Repeat Accuracy: 0.01%)
• Multiple Time Range: From 0.01 Sec to 999 Hrs
• Time base selection via key board
• Time Setting via High Quality Push wheel switches
• Configuration at power on (To prevent unauthorized tampering)
• Universal supply voltage ranges from 90 To 270 VAC
• Available in 3 Standard DIN sizes

Product Details:

QIS offer Autonics Counter/Timer;
Available to set 6 digits(0.00001 to 999999) prescale value(4digit : 0.001 to 9999)
Built-in Modbus communication function(Communication model)
Available to set the One-Shot output time in 10ms.(0.01sec. to 99.99sec.)
Increase contact capacity to 5A(CTS, CTM Series)
Available to set Count Start Point.(Initial value)
Improved to select memory protection function in the indicator
Added BATCH counter function(CTM Series)
Added Counter Up-1 / Up-2 / Down-1 / Down-2 input modes
Added Counter TOTAL / HOLD operation modes in the indicator
Added Timer TOTAL / HOLD / On Time Display operation modes in the indicator
Added Timer INT2 / NFD / NFD.1 / INTG output modes
Added Timer range 999.999s / 9999m59 / 99999.9h

Product Details:

The SRHL1 series single phase solid state relays feature integrated heatsinks for excellent heat dissipation effiency. The left/right terminal layout provides more flexibles installation options. The SRHL1 series is available in zero cross turn-on and random turn-on models and also feature alarm functions of safer operation. The units support both DIN rail mount/panel mount mehtods.

Product Details:

The 4-channel relay module features visualization of four switching states through LEDs. The relay outputs are each equipped with an AC 230V/3A changeover contact. A removable terminal strip with push-in technology is available for each channel. This saves you time while ensuring reliable wiring.

Product Details:

QIS can design, fabricate, configure, testing, installation and commissioning of Control panel for Hydraulic Press, which will be used in Brake linning industies, Rubber processing etc..

Features :

• MS powder quoted free standing control panel
• 7" TFT Touch Screen display
• PLC with communication ports, upto 210 I/O points
• SMPS, Isolation transformer, terminal blocks and accessories.

Product Details:

WECON VD2 Servo Drives ( 0.4 t0 0.75KW) 220V

Servo Drive Features

◇ Using dual core DSP + FPGA processing, the response speed is increased by 4 times;

◇ 17-bit or 23-bit absolute value, incremental encoder interface (optional);

◇ Engine coating protection to prevent corrosion damage;

◇ Automatic parameter auto-tuning;

◇ Monitoring of instantaneous charge rate and average charge rate;

◇ Playback of the crash log panel;

◇ Holding brake output control;

◇ Internal multi-segment position instruction;

◇ Real-time automatic identification of load inertia;

◇ Pulse rate monitoring.

Product Details:

PI3070ig HMI

uCPU A35 1.2GHz, 128M Flash, 128M DDRAM

uDisplay:7 inches; Resolution: 800*480; Display color: 16,000k colors

uInterfaces: a serial port. COM1: RS232, RS422 or RS485(choose one of two), RS485.

uUSB interfaces: USB Host/USB Client

u Remote monitoring and WVPN pass-through download.

u3070ig-C supports related functions of V-NET, Ethernet pass-through download and sync data to cloud.

Product Details:

The 8-channel analog input module offers you up to eight analog inputs for resistance thermometers with a two-wire circuit. This variant still features an overall width of 22.5 mm, which helps you save space when arranging the modules in your control cabinet

Product Details:

We sells all model / range of Delta AC Drives, VFD’s.

Delta VFD-M Series – SVC Micro Drives

FEATURES

Sensorless Vector Micro AC Drive. The compact design is ideal for small and medium horsepower applications. The M drive is designed to provide an ultra-low-noise operation, and includes several innovative technologies that reduce interference.

Details :

• Adjustable V/f curve and vector control
• Carrier frequency up to 15 kHz
• Auto torque boost & slip compensation
• Built-in PID feedback control
• Built-in MODBUS communication, baud rate up to 38400 bps
• 0 speed holding function
• Built-in sleep / revival function
• Support communication module (DN-02, LN-01, PD-01)

APPLICATIONS

Packing machine; dumpling machine; treadmill; temperature/humidity control fan for agriculture and aquaculture; mixer for food processing; grinding machine; drilling machine; small size hydraulic lathe; elevator; coating equipment; small size milling machine; robot arm of injection machine (clamp); wood machine (two-side woodworking planer); edge bending machine, elasticizer, etc.

Product Details:

PR series inductive proximity sensor feature solid sensing performance and excellent noise immunity. Available in various sizies and sensing distances, the standard cylindrical inductive sensors can be used in diverse applications requiring non-contact detection of metallic objects.

Features :
- Excellent noise immunity
- Simple operation, reliable performance and high durability
- Built in surge protection unit
- Built in over current protection
- Built in reverse polarity protection circuit
- Operation indicator (LED)
- IP67 protection

Additional Information:

• Delivery Time: Ex stock

Product Details:

We are a leader in offering best quality Alarm Annunciator.  

We have huge reputation in market for offering quality focused products that finds substantive place in various industries. 

The technology at our organization is upgraded at regular intervals to ensure we keep updated with latest market advancements.

Product Details:

PS/PSN series rectangular inductive proximity sensors feature excellent noise immunity with specilized sensor devloped by Autonics. Various sizes are available for applicaiton.

Features:
- Excellent noise immunity
- long life cycle, reliable performance, economincal
- operation indicatior (LED)
- Built in surge protection
- Built in overcurrent protection
- IP 67 protection

Additional Information:

• Delivery Time: Ex stock

Product Details:

Product description

• 4 (AOMS-4U) or 8 (AOMS-8U) Analog Output Channels
• Each Channel Independently Programmable for DC Current (0-20 mA, 4-20 mA & 0-10 mA) or Voltage (0-5 V, 1-5 V & 0-10 V) Output
• 14 Bit Output Signal Resolution
• Programmable Min / Max Counts Corresponding to Signal Low & Signal High Outputs
• Programmable Fail-Safe Output Signal Level Against Communication Link Failure
• Three-way Isolation Eliminates Potential Ground Loops between Power, Outputs and RS485 Serial Port
• Supports Coils (Bits) & Bit-Mapped Registers MODBUS Data Type for Most Parameters
• 2-wire, Half-Duplex, Start-Stop Synchronized RS485 Serial Port
• Industry Standard MODBUS RTU Protocol with Programmable ID, Baud Rate & Parity
• Compact DIN-Rail Mount Enclosure : 22.5(W) X 101(H) X 119(D), mm
• Wide Supply Voltage Range : 18 ~ 32 VDC (24 VDC Nominal)
• Free PC Tool for Easy Configuration and Parameter Settings

Product Details:

Product description

• 8 (DIMS-8) or 16 (DIMS-16) Digital Input Channels
• Input Types Supported
  • Dry (Potential-free) Open/Close Contact
  • High/Low Voltage Levels
  • PNP & NPN Sensor with +12VDC Internal Excitation
  • PNP & NPN Sensor with 5 to 30VDC External Excitation
• Independent Programmable Filter Time Constant for each Input
• Monitors Instantaneous High/Low Input Status
• Monitors Latched Low to High & High to Low Transition Status
• Supports Discrete Coil (Bits) & Input Register (Bit-Mapped) Modbus Data Type for Status Reading
• 2-wire, Half-Duplex, Start-Stop Synchronized, Isolated RS485 Serial Port.
• Industry Standard Modbus RTU Protocol with Programmable Slave ID, Baud Rate & Parity
• Compact DIN-Rail Mount Enclosure : 22.5(W) X 101(H) X 119(D), mm
• Wide Supply Voltage Range : 18 ~ 32 VDC (24 VDC Nominal)

Product Details:

Product description

• 12 Digital Output Channels
• Sink Output Version :
  Open Drain : 5 to 30 V, 200 mA max.
• Source Output Version :
  VCC : 5 to 30VDC, 100mA per Channel
• Supports Discrete Coil (Bits) & Input Register (Bit-Mapped) Modbus Data Type for Status Reading
• 3 Digital Output Function Modes
  • On-Off
  • Re-Triggerable Single Pulse with Programmable Pulse-ON Time
  • Continuous Pulse Train with Programmable Pulse-ON & Pulse-OFF Time
• Programmable Fail-Safe Output States Against Communication Link Failure
• 2-wire, Half-Duplex, Start-Stop Synchronized, isolated RS485 Serial Port with Industry Standard Modbus RTU Protocol
• Programmable Slave ID, Baud Rate & Parity
• Compact DIN-Rail Mount Enclosure : 22.5(W) X 101(H) X 119(D), mm
• Wide Supply Voltage Range : 18 ~ 32 VDC (24 VDC Nominal)

Product Details:

QIS offers Large display production counters , which will be used in indutry production floors.

Display Type : 4 digits
LED Size : 2", 4" , 6" and 8"
Input : contact, NPN, PNP
Output : Relay
Reset : front panel switch
Power supply : 230VAC, 24VDC
Sensor exicitation : 24VDC

Product Details:

Details - High Quality Rotary Encoder
 

1) Pulse rate 10-4096PPR incremental
2) 6mm or 8mm stainless steel shaf

Rotary EncoderToky HY50 series Rotary Encoder with following features:

1) Housing dimension 50mm, to be used in light industry;

2) Pulse rate from 10 to 2500ppr, providing many choices to customers;

3) Metal housing, upgrading the ability of shock resistance;

4) 8mm diameter stainless steel shaft improves the stability and protection;

5) Protection is up to IP54. With reverse connection protected and short-circuit proof;

6) With cable output, waterproof at the outlet;

7) With up to 8 kinds of output mode, with or without inverted signal.

Product Details:

The FRENIC-Mini (C2) is a general purpose micro drive that is easy to use and packed with features in a compact housing.

Standard functions of the FRENIC-Mini include high starting torque, synchronous motor control, optimum energy savings, PID control and built-in Modbus RTU.

The standard rating on the FRENIC-Mini is IP20 UL Open Type (UL50). The optional NEMA/UL Type 1 kit allows you to use this drive in stand alone applications and is used for finger protection for indoor use. There is also a DIN rail adapter (up to 5hp) and a remote/USB keypad accessory.

The FRENIC-Mini is available in:

• 1 phase, 115V from 1/8 to 1hp
• 1 phase, 230V from 1/8 to 3hp
• 3 phase, 230V from 1/8 to 20hp
• 3 phase, 460V from 1/8 to 20hp

The Fuji FRENIC-Mini has a simplified torque vector control system with automatic torque boost function. 

• Fan, Pump applications: automatic energy-saving function, PID control function, and cooling fan ON/OFF control function
• Target industries include transverse conveyors, conveyors for food processing, mixers, chemical equipment and wood processing machines

With improved voltage control capability and reduced motor instability at low speed (about half compared with that of conventional models at 1Hz), the Mini can be used to drive mixers, chemical equipment, wood processing machines and a range of other applications.

Fuji is the world's top manufacturer of general purpose inverters in the 5hp or below class!

Effective July 1, 2015: FRENIC-Mini now has the following features (Part Number changed from 'C1S' to 'C2S':)

• Compatible with Fuji Electric's loader software
• Firmware for permanent magnet motors
• RS485 serial port with standard MODBUS RTU communication
• Same size and footprint as the old FRENIC-Mini

Product Details:

SP series DIN Rail Switching Mode Power Supplies
The SP series simple type switching mode power supplies feature compact sizes with 3W ouput power source 5 VDC. 12 VDC, 24 VDC ouput voltage options are available. The units can be clipped on the DIN rails or mounted using standared M4 sized screws for convenient installation. The SP series also feature built-in over current protection circuits. 

Product Details:

Product Details:

QIS has capability to design, detailed engineerinng, configuration, testing, FAT, SAT and commissiioning of SCADA system to suit customer applicaiton.

Features :

• Server-Client system configuration
• Scalable upto 4000 I/O points
• Variety of commuication interfaces such as Modbus TCP/IP, Profinet, Serial protocols
• Real time server, Alarm and Event storate, History data storate and view.
• Sinlge or Redundant configuration
• Firewall for cyber security.

Product Details:

Details proximity sensor & proximity switch

1) inductive or capactive
2) Sensing distance 2-10mm
3) easy connection,NPN/PNP output

Inductive Proximity Sensor

 

TOKY Inductive proximity sensor with following features:

 

TK series column shape inductive type with follow features:
1) Inductive type, sensitive to metal;
2) Optional current output, including 200 and 300mA;
3) Optional sensing distance, from 2mm to 15mm;
4) Different column diameter, including M8, M12, M18, M22, M30;
5) Different application, DC 3 wires, DC2 wires or AC 2 wires.

 

TK series square shape inductive type has below features:
1) Inductive type, sensitive to metal;
2) Square sensing face, with different dimension;
3) Optional current output, including 200 and 300mA;
4) Optional sensing distance, from 5mm to 35mm;
5) Different application, DC 3 wires or AC 2 wires.

 

TC series column shape capacitive type with follow features:
1) Capactive type, sensitive to different material, including metal or non-metal;
2) Current output 200 mA;
3) Optional sensing distance, including 10mm and 25mm;
4) Different column diameter, including M18, M30;
5) Different application, DC 3 wires or AC 2 wires.

Product Details:

JUMO TYA-432 thyristor power switch (709010)

• Without heat sink

JUMO TYA-432 thyristor power switch (709020)

• Single phase, 3 phase version
• With heat sink

Product Details:

The SPR1 series single - phase power controllers are ideal for installation in limited spaces with slim body sizes. The LED display allows real-time monitoring of control output, load voltage, load power, load resistance and heat-sink temperature. The controllers feature phase control, cycle control and ON/OFF control method.

Product Details:

The 12-channel digital input/output module offers you flexibility through freely selectable DC 0/24V digital input or output channels. Permissible loading of up to 500 mA per digital output ensures convenient system planning.

Product Details:

QIS can provide automation programming services for industrial client. Main activites as below.

• PLC logic development
• System migration
• System Detailed Engineering
• HMI development
• Networking
• SCADA software development.
• Site trouble shooting and upgradation of existing systems.

Product Details:

Features and Benefits

• Compatible with USB 2.0
• 12 Mbps USB data rate
• 15N high retention USB type B connector
• Selectable RS-232, RS-422, 4-wire RS-485, and 2-wire RS-485
• Certified drivers provided for Windows
• 15 KV ESD protection for all serial ports
• 2 KV optical isolation protection
• Full modem status LEDs
  

   

Instant Plug & Play

The USB-to-serial converters allow you to connect 1 RS-232/422/485 device to your laptop or workstation through the USB (Universal Serial Bus) port. These plug & play USB solutions are compatible with both new and legacy RS-232/422/485 devices, and are perfect for mobile, instrumentation, and point-of sale applications.

Product Details:

V-BOX H SERIES

Main Features:

V-BOX is a device for use in remote debugging, web scada, API interface, app monitoring.

*Get data via RS-232 / RS-485 / Ethernet communication, offer Modbus RTU / Modbus TCP communication.

*Supports communication protocols of the main brands of PLC, frequency inverters, network analyzers, among others.

*Connects to the cloud platform through Ethernet, Wifi, 4G connectivity.

*Remote monitoring with upload and download option of PLC programming (Wecon).

*Offers WVPN for remote connection to different PLC brands.

*OPC access.

*Development of Scada in the cloud.

*Datalogger and download of data, alarms and history directly to Excel.

*Access available from mobile devices through the V-Box app (Android / IOS)

Product Details:

Product description

• Robust, High Resolution, Accurate Micro-Controller Based Design
• Slim size of 35mm for Single and Dual Outputs
• Versions Available for Variety of Input and Output Types
• Optional, 24VDC/30mA Excitation Supply for Transmitter. Isolated from Power, OP1 & OP2
• 1.5KV AC Isolation between Power Supply, Input, OP1 & OP2 (OP2 available in ISOSIG-35D model)
• High Resolution Input : 16-bit Resolution ADC
• High Resolution Output : 10,000 parts
• Programmable Burnout (Scale Up / Scale Down)
• Front Panel Zero / Span Adjustment through Multi-turn Trim-Pots
• Programmable Zero Offset for RTD / Thermocouple Inputs
• In-built Lead Resistance Compensation for RTD Inputs
• In-built Cold Junction Compensation for Thermocouple Inputs
• Versions Available for AC (85~265 VAC) & DC (20~32 VDC) Supply
• Din-Rail Mounting : 35(W) X 75(H) X 107(D)

Product Details:

DS Series 3 Phase Digital Voltage/Ampere Meter features:

• Measure each phase voltage/ampere of 3 phase electricity
• 3 lines 4 digit LED display, easy to read
• With two alarm output, easy & useful to monitor each phase
• Some model with 4-20mA transform current output and RS485 communication function

Additional Information:

• Item Code: DS-Series